Main Inventory

Gus Pech 3000

Gus Pech 3000

Great for Hammer Drilling/Rock/Mud or High Speed Coring

3 winches, tilting front jack – 8,020 hours. On 1998 International 4900. No mud pump.

Yale Electric Forklift

Yale Electric Forklift

Electric – 24 Volt Battery – 6,390 Hours

3,000lb capacity – 7,200lbs weight w/ Battery – 276″ Load Height – 10′ Tall – 41″ Wide

3 Available

DoAll Mill

DoAll Mill

Vertical or Horizontal Milling Machine

Caterpillar 3406 B

Caterpillar 3406 B

Caterpillar Diesel 3406 B 400hp – 5,000 hours

Hyster Fork Drill

Hyster Fork Drill

Traveling height 89″, length 10’6″, width 54″, 10′ drill rod, hammer capacity 3″ to 24″, weight 14,000 lbs., Perkins diesel powered, 9,000 lbs winch, 9,000 ft – lbs torque, 8,000 lbs pullback, table opening 24 1/4″ water injection, oil injection, 3 1/2″ Reg Thread.

1988 Watson 2500

1988 Watson 2500

1988 Watson 2500 Cummins 6b 5.9 175hp low hours on engine, rebuilt pull master m25 inner bar winch, rebuilt tower cylinders, new inner/outer bar swivels, rebuilt hydraulic swivel, 81,000 ft-lbs torque. 25k crowd. 6″ and 4 1/4″ bars.      38′ 4”tall. 64,000 lbs

1982 Williams LDH60T

1982 Williams LDH60T

7” Outer Bar, 5 1/4” Inner Bar, Cummins 6BT, 175 HP, 6” Jacks, Mounted on 1982 Hendrickson Carrier Model 600-D0H, 4 axles

1990 Texoma Taurus XL

1990 Texoma Taurus XL

Mounted on CCC4 axle carrier with a CAT 3406 Engine, Up to 12′ Drilling Diameter, 120′ depth, Cummins 6 Cyl. Lower 144,000 ft-lbs torque, 38,000 Lbs. Hoist, 50,000 lbs Crowd

1967 Williams LDH30T

 1967 Williams LDH30T

DG rotary 7” outer bar, 5 ¼” inner bar, 6-BT Cummins upper, CAT 3306T lower, Mounted on 1976 Hendrickson Carrier Model 600-D-0H, 4 axles, w/ Hy-Rail Gear, 33’L x 13’6” H x 8’3”W, 30’ in drill position, Side reach 13’

Texoma 650

Texoma 650

Mounted on a 2000 Peterbilt 379 Truck, 3 axle

2002 IMT AF80

2002 IMT AF80

IMT AF80 Hydraulic Drill Rig mounted on TOR DR8690 Carrier with Caterpillar C10 Engine with 335Hp @ 2,100rpm, 10 Speed Eaton Fuller Transmission, 8 x 6 wheel drive and a Gross Operating weight of 78,620 lbs. The AF80 Drill is a Caterpillar 315B Power Module with Caterpillar 3054 engine with 114 Hp @ 2100 rpm, maximum drilling torque of 60,000 ft-lbs @ 7 rpm, Crowd pressure of 22,500 ft-lbs, Main winch pull of 20,000 ft-lbs and a 3 element Kelly bar with a Digging depth of 24m or 78′.

1993 Gill Beetle B137S4D

1993 Gill Beetle B137S4D

(7) 10′ Drill Rod, Water & Oil Injection, Auxiliary Controls, Power Hose Reel w/ 200 ft of 2″ Hose, A/C Cab, 353 Detroit Diesel, 3563 Hours, 3.75″ Hammer w/ 4.5″ 12 Spline Bit. 3.5” reg thread.

2003 Watson 1100CM

2003 Watson 1100CM

Track Mount drill rig with 8.5’W x 11.5’H, 35′L (w/ Mast), 18′L (Tracks), 35,000lbs, 1,904 hrs, 6″ outer bar, 4 1/4″ inner bar, 2′ to 4′ diameter, 50 depth, 41,000 ft-lbs torque, 18,000 lbs hoist, 23,000 lbs crowd, 40′ height.

1997 Watson 3100CW

1997 Watson 3100CW

New Cables, New Hydraulic Cylinders, New Engine, Rebuilt Turntable bearing, Tilting Carbody, 11’11” Wide, Up to 8′ Diameter, Up to 80’ Deep, Torque 113,000 ft-lbs, Crowd 50,000, Hoist 25,000.

Williams LDH90T

Williams LDH90T

Mounted on Pierce Pacific Tracks, 20º tilt, 8″ outer bar, 6″ inner bar, up to 90’ Depth

Continuous Flight Augers

Continuous Flight Augers

Continuous Flight Augers In various Sizes ranging from 12″ Diam to 22″ Diam

REICHdrill C-550-DII

REICHdrill C-550-DII

Crawler mounted Blast Hole Drill, Upper Engine Replaced: CAT 3406 diesel w/ 3,552 hours, 900/350 on-board compressor, cab. Weight: 60,000lbs., height: 46’ (mast up), width: 10’. Rated for 5” – 6 ¾” holes to 210’ depth. 4 + 1 indexing barrel loader. Bit load capacity: 40,000lbs. Excellent condition

1999 Schramm 450WS Dual Rotary

1999 Schramm 450WS Dual Rotary

1999 International chassis with 1999 Schramm Drill, 280’ of 4 ½” drill rod with 3 ½” reg pin, Errickson Casing Rotator, 850/350 compressor w/ cat3406d engine

22" Mill Tooth Roller

22

22″ – 7-5/8″ Regular Thread Mill Tooth

23-1/2" Hole Opener

23-1/2

7-5/8″ Regular Thread w/ 4-1/2″ Regular Adapter

Diverters

Diverters

10″ or 16″ Diverters with 4″, 5″ or 6″ discharge ports. Adapters made to fit any size casing.

IR DM4

IR DM4

Crawler drill rig with Errickson CR-16 Dual Rotary Drive. Maximum torque: 80,000 FT. LBS., Static Load: 315,000 LBS. Casing size: 4” – 16” diameters. Package includes 10” diverter.

1997 Soilmec R515J

1997 Soilmec R515J

Track Mount drill rig with low clearance setup, CAT 3306 engine, 54 ton operating weight, 154 rpm spin off, max drilling speed 26rpm, rotary head with 2 drilling speeds, telescopic kelly bar. Dual Rotary CR-26 Drive.

Roller/Hole Opener w/ Pilot Bit

Roller/Hole Opener w/ Pilot Bit

23″ Roller Bit Hole Opener – 15″ Pilot bit

Rollers need “Help”

112S Chuck - Excellent Used

112S Chuck - Excellent Used

Excellent used hammer chuck – 112S

Large Quantity 4" Rock Bits

Large Quantity 4

IR 3.5 4″ Bits – IR/Sandvik/Mincon

8 Spline – 181mm Shaft – 48 Available

112 Hammer

112 Hammer

Hammer w/ 16″ Over-Hammer Shroud for 17-1/2″ 112 Bit

Box Lead with Errickson CR-26 Dual Rotary Drive

Box Lead with Errickson CR-26 Dual Rotary Drive

Box Lead with Errickson CR-26 Dual Rotary Drive. Maximum torque: 180,000 FT. LBS., Static Load: 1,400,000 LBS. Casing size: 4” – 36” diameters. Package includes 16” diverter.

Quick Change Over-Hammer Stabilizer

Quick Change Over-Hammer Stabilizer

MADE TO ORDER – QUICK CHANGE OVER-HAMMER STABILIZERS

Built in house.

Drill Bit Complete Inventory

Drill Bit Complete Inventory

Multiple sizes & models. Drill fitment listed in right column. Inventory is likely to change frequently. Call for availability & pricing.

Showing 31 - 60 of 62 items<123>