DUAL ROTARY |
||||
| Dual Rotary Casing Drives allow you to drive casing from 4” – 36” simultaneously while boring the hole. Drill anytime, anywhere in any geological formation. This method of drilling also helps to eliminate hole collapse and provides a more predictable, uniform and stable hole. | ||||
|
|
 |
|||
| 1997 SOILMEC R515J | 1999 Schramm-450ws Dual Rotary |
|||
| Track Mount drill rig with low clearance setup, CAT 3306 engine, 54 ton operating weight, 154 rpm spin off, max drilling speed 26rpm, rotary head with 2 drilling speeds, telescopic kelly bar. | One 1999 International chassis with 1999 Schramm Drill, 280’ of 4 ½” drill rod with 3 ½” reg pin, 75k truck miles, 10,500 hrs on rig, New Errickson Casing Rotator, 850/350 compressor w/ cat3406d engine. | |||
|
FOR SALE/RENT |
FOR SALE/RENT | |||
 |
 |
|||
|
Crane Leads |
IR DM4 | |||
| Box Lead with Errickson CR-26 Dual Rotary Drive. Maximum torque: 180,000 FT. LBS., Static Load: 1,400,000 LBS. Casing size: 4” – 36” diameters. Package includes 16” diverter. | Crawler drill rig with Errickson CR-16 Dual Rotary Drive. Maximum torque: 80,000 FT. LBS., Static Load: 315,000 LBS. Casing size: 4” – 16” diameters. Package includes 10” diverter. | |||
| FOR RENT | FOR SALE |
|||
AIR RIGS/ROCK DRILLS |
||||
 |
 |
 |
||
| 1995 DAVEY KENT-DK50RA | HYSTER-FORK DRILL | REICH Drill C-550-DII | ||
| Crawler Rotary Drill Rig, 3 1/2 reg pin down, 3 rods, 2 spd wirth head, pullmaster winch, Roper mud pump, model# PG-4, 4 cylinder diesel, air cooled, 8’6″H at lowest mast height, 53″ wide, Very god Condition. 2 extra tower sections included with rig. Serial #12693. | Traveling height 89″, length 10’6″, width 54″, 10′ drill rod, hammer capacity 3″ to 24″, weight 14,000 lbs., Perkins diesel powered, 9,000 lbs winch, 9,000 ft – lbs torque, 8,000 lbs pullback, table opening 24 1/4″ water injection, oil injection, 3 1/2″ Reg Thread. | Crawler mounted Blast Hole Drill, Upper Engine Replaced: CAT 3406 diesel w/ only 1,199 hours, 900/350 on-board compressor, cab. Weight: 60,000lbs., height: 46’ (mast up), width: 10’. Rated for 5” – 6 ¾” holes to 210’ depth. 4 + 1 indexing barrel loader. Bit load capacity: 40,000lbs. Excellent condition. | ||
| FOR SALE/RENT | FOR SALE/RENT | $95,000 | ||
 |
 |
 |
||
| 2006 BOART LONGYEAR – DeltaBase 102 | 2000 GILL BEETLE-150/C/D | 1993 GILL BEETLE-B137S4D | ||
| B2 crawler mounted, Deutz 197hp diesel engine, 18,800 lbs. torque, variable piston pump with load sensing and torque control, drills vertical, horizontal and off side. L – 23’5” (mast down), H – 8’9” (mast down), W – 7’4”. Weight: 31,000 lbs. (w/o tooling). Double Headdrilling unit capability. | 10′ drill rod, 4″ diameter, Cummins B3.9-P engine, 4400 ft lbs torque, 20,000 lbs pull down, 18,000 lbs pull back, 6200 hours, enclosed cab with air conditioning. Height 8’ 10”, Width 8’8”, Length 26’7”. | (7) 10′ Drill Rod, Water & Oil Injection, Auxillary Controls, Power Hose Reel w/ 200 ft of 2″ Hose, A/C Cab, 353 Detroit Deisel, 3563 Hours, 3.75″ Hammer w/ 4.5″ 12 Spline Bit. 3.5” reg thread. | ||
| FOR SALE/RENT | FOR SALE/RENT | FOR SALE/RENT | ||
AUGER RIGS (Track Mounted) |
||||
 |
 |
 |
||
| 2003 Watson 1100CM | 1997 Watson 3100CW | WILLIAMS LDH90T | ||
| Track Mount drill rig with 8’6″ wide. 11’6″ high, 35′ long, 18′ long tracks, 35,000lbs, 1,904 hrs, 6″ outer bar, 4 1/4″ inner bar, 24″-48″ diameter, 50 depth, 41,000 ft bs torque, 18,000 lbs hoist, 23,000 lbs crowd, 40′ height. | New Cables, New Hydraulic Cylinders, New Engine, Rebuilt Turntable bearing, Tilting Carbody, 11’11” Wide, Up to 96” Diameter, Up to 80’ Deep, Torque 113,00 ft lbs, Crowd 50,000, Hoist 25,000. | Mounted on Pierce Pacific Tracks, 20 degree tilt, 8” outer bar, 6” inner bar’ up to 90’ | ||
| FOR RENT | FOR RENT | FOR SALE/RENT | ||
AUGER RIGS (Truck Mounted) |
||||
 |
 |
 |
||
| 2002 IMT AF80 | TEXOMA 650 | 1990 Texoma Taurus XL | ||
| IMT AF80 Hydraulic Drill Rig mounted on TOR DR8690 Carrier with Caterpillar C10 Engine with 335Hp @ 2 100rpm, 10 Speed Eaton Fuller Transmission, 8 x 6 wheel drive and a Gross Operating weight of 78 620.00 lbs.The AF80 Drill is a Caterpillar 315B Power Module with Caterpillar 3054 engine with 114 Hp @ 2100 rpm, maximum drilling torque of 60 000 ft lbs @ 7rpm, Crowd pressure of 22 500 ft lbs, Main winch pull of 20 000 ft lbs and a 3 element Kelly bar with a Digging depth of 24 meters / 78 foot. | Mounted on a 2000 Peterbilt 379 Truck, 3 axles, | Mounted on CCC4 axle carrier with a CAT 3406 Engine, Up to 12 ft Drilling Diameter, 120 foot depth, Cummins 6 Cyl Lower 144,000 Ft/Lbs Torque, 38,000 Lbs. Hoist, 50,000 Lbs Crowd | ||
| FOR SALE/RENT | NOT FOR SALE | FOR RENT WITH OPERATOR | ||
 |
 |
 |
||
| 1967 Williams LDH30T | 1982 Williams LDH60T | 1968 Williams LDH40T | ||
| DG rotary 7” outer bar, 5 ¼” inner bar, 6-BT Cummins upper, CAT 3306T lower, Mounted on 1976 Hendrickson Carrier Model 600-D-0H, 4 axles, w/ Hy-Rail Gear, 33’L x 13’6” H x 8’3”W, 30’ in drill position, Side reach 13’ | 7” Outer Bar, 5 1/4” Inner Bar, Cummins 6BT, 175 HP, 6” Jacks, Mounted on 1982 Hendrickson Carrier Model 600-D0H, 4 axles | Has a Cummins 6CT engine, 7” Outer Bar, 5 ¼” Inner Bar, Full turntable w/ jacks, sliding rear jacks for 10’ drill bit clearance, Max diameter 10’, Trailer Mount | ||
| FOR SALE | FOR SALE/RENT | FOR SALE | ||
 |
 |
 |
||
| 1980 Williams LDH40T | 1985 Williams LDH80T | Watson 2500 | ||
| 8” Outer Bar, 6” inner bar, with new Deutz BMF1013c water cooled engine, Mounted on 1980 Hendrickson Carrier, Model 600-D0H, 4 axles, 290 Cummins Engine. | Pressure Digger on Hendrickson carrier, Max Diameter is 96”, 6” Outer bar with 4 ¼” inner, full turntable, Air clutches, 6BT Cummins Upper, NTC350 Lower. |
1988 Watson 2500 cummins 6b 5.9 175hp low hours on engine, rebuilt pull master m25 inner bar winch, rebuilt tower cylinders, new inner/outer bar swivels, rebuilt hydrolic swivel, 81,000 torque. 25k crowd. 6-4 1/4 bars. 38′ 4”tall. 64,000 pounds. rig ready to drill needs nothing. FOR SALE/RENT |
||
| FOR SALE/RENT | FOR SALE/RENT | |||
