2018 ChemGrout CG550/031/GH/ES
Gas powered, electric start, grout machine w/ water batcher & hose. 70 gallon mix tank/45 gallon hopper/3” piston pump. 16 GPM maximum output. Comes with 50’ x 1.25” used grout hose.
10′ drill rod, 4″ diameter, Cummins B3.9-P engine, 4400 ft lbs rotation torque, 20,000 lbs pull down, 18,000 lbs pullback, 6,200 hours, enclosed cab with air conditioning., 60′ drill rod, Automatic incliner, No charge for delivery to Newark. Height 8’10” (mast down), Width 8’8″, Length 26’7″ (mast down), 20’3″ (mast up). 2 3/8″ Drill Rod.
Deutz 225 Horse Water Cooled Engine. 8″ Outer x 6″ Inner Bar. Car Body Tilt. Pierce Pacific Tracks – 12′ Wide. Will Separate
Low Clearance. Cummins 6CT Engine. 40′ Mast – 7″ Outer Bar/5-1/4″ Inner Bar. Full turn table w/ jacks – Capable of 10′ Diameter – Sliding rear jacks for 10′ drill bit clearance. Trailer Mounted – 3 Axle
NEW Final Drive – Yutong Model 300. Rexroth Motors – Brevini Planetary. 19″ OD bar – Set up for 32″ wide x 3-1/4″ deep rails. Adjustable – With new 19″ OD Kelly Bar
Bauer Casings w/ Core Barrel Bits/Ends. Multiple sections – 16-1/2″, 24″, 37″, 49″. 2-1/2″ Pins
2006 Boart Longyear Delta Base DB102 Anchor Drill. 9,000 ft-lbs of torque. B2 Crawler, Deutz 197hp Water Cooled Diesel. Variable piston pump w/ load sensing; torque control. Double head drilling unit. 1,415 hours; has a new computer! Variable piston pump with load sensing and torque control, drills vertical, horizontal and off side. L – 23’5” (mast down), H – 8’9” (mast down), W – 7’4”. Weight: 31,000 lbs. (w/o tooling). Double head drilling unit capability.
1995 Davey Kent DK50RA Crawler
Crawler Rotary Drill Rig, 3 1/2 reg pin down, 3 rods, 2 spd wirth head, pullmaster winch, Moyno mud pump, model# PG-4, 4 cylinder diesel, air cooled, 8’6″H at lowest mast height, 53″ wide, Very god Condition. 3 extra tower sections included with rig.
Electric – 24 Volt Battery – 6,390 Hours
3,000lb capacity – 7,200lbs weight w/ Battery – 276″ Load Height – 10′ Tall – 41″ Wide
3 Available
1988 Watson 2500 Cummins 6b 5.9 175hp low hours on engine, rebuilt pull master m25 inner bar winch, rebuilt tower cylinders, new inner/outer bar swivels, rebuilt hydraulic swivel, 81,000 ft-lbs torque. 25k crowd. 6″ and 4 1/4″ bars. 38′ 4”tall. 64,000 lbs
7” Outer Bar, 5 1/4” Inner Bar, Cummins 6BT, 175 HP, 6” Jacks, Mounted on 1982 Hendrickson Carrier Model 600-D0H, 4 axles
Mounted on CCC4 axle carrier with a CAT 3406 Engine, Up to 12′ Drilling Diameter, 120′ depth, Cummins 6 Cyl. Lower 144,000 ft-lbs torque, 38,000 Lbs. Hoist, 50,000 lbs Crowd
New Cables, New Hydraulic Cylinders, New Engine, Rebuilt Turntable bearing, Tilting Carbody, 11’11” Wide, Up to 8′ Diameter, Up to 80’ Deep, Torque 113,000 ft-lbs, Crowd 50,000, Hoist 25,000.