Main Inventory

2018 ChemGrout CG550/031/GH/ES

2018 ChemGrout CG550/031/GH/ES

Gas powered, electric start, grout machine w/ water batcher & hose. 70 gallon mix tank/45 gallon hopper/3” piston pump. 16 GPM maximum output. Comes with 50’ x 1.25” used grout hose.

Halco 17" Hammer Bit

Halco 17

Complete Halco 132 17″ Bit

2000 Gill Beetle 150/C/D

2000 Gill Beetle 150/C/D

10′ drill rod, 4″ diameter, Cummins B3.9-P engine, 4400 ft lbs rotation torque, 20,000 lbs pull down, 18,000 lbs pullback, 6,200 hours, enclosed cab with air conditioning., 60′ drill rod, Automatic incliner, No charge for delivery to Newark. Height 8’10” (mast down), Width 8’8″, Length 26’7″ (mast down), 20’3″ (mast up). 2 3/8″ Drill Rod.

Vermeer 2.875" Horizontal Drill Rod

Vermeer 2.875

2.875″ Vermeer Horizontal Drill Rod

P&H Yard Crane

P&H Yard Crane

Useable P&H Yard Crane – Cummins Up & Down

12.75" Drill Rod

12.75

7 Available

12-3/4″ x 7’7″ Long, 6-5/8″ Regular Pin & Box, 1-1/2″ Break Out holes

16" Drill Rod - 5-1/2" IF Threads

16

20′ Long Drill Rod – 16″ Diameter w/ 5-1/2″ IF Threads

4" Drill Rod BECO Thread

4

4″ x 10′ – 3″ Wrench – BECO Thread – 9 Total

4" Regular Thread

4

4″ x 6’7″ Long w/ 3″ Wrench & 2-7/8″ Regular Thread

Truck Stinger

Truck Stinger

Stinger – 11′ Axle to Pivot w/ Air-Ride & 22.5/445 Tires

Williams-Hughes LDH60T Yellow

Williams-Hughes LDH60T Yellow

Deutz 225 Horse Water Cooled Engine. 8″ Outer x 6″ Inner Bar. Car Body Tilt. Pierce Pacific Tracks – 12′ Wide. Will Separate

Williams-Hughes LLDH40T

Williams-Hughes LLDH40T

Low Clearance. Cummins 6CT Engine. 40′ Mast – 7″ Outer Bar/5-1/4″ Inner Bar. Full turn table w/ jacks – Capable of 10′ Diameter – Sliding rear jacks for 10′ drill bit clearance. Trailer Mounted – 3 Axle

Yutong 300

Yutong 300

NEW Final Drive – Yutong Model 300. Rexroth Motors – Brevini Planetary. 19″ OD bar – Set up for 32″ wide x 3-1/4″ deep rails. Adjustable – With new 19″ OD Kelly Bar

Bauer Casing/Barrel Bit

Bauer Casing/Barrel Bit

Bauer Casings w/ Core Barrel Bits/Ends. Multiple sections – 16-1/2″, 24″, 37″, 49″. 2-1/2″ Pins

2006 Boart Longyear

2006 Boart Longyear

2006 Boart Longyear Delta Base DB102 Anchor Drill. 9,000 ft-lbs of torque. B2 Crawler, Deutz 197hp Water Cooled Diesel. Variable piston pump w/ load sensing; torque control. Double head drilling unit. 1,415 hours; has a new computer! Variable piston pump with load sensing and torque control, drills vertical, horizontal and off side. L – 23’5” (mast down), H – 8’9” (mast down), W – 7’4”. Weight: 31,000 lbs. (w/o tooling). Double head drilling unit capability.

Sullair Air End

Sullair Air End

Green air end for Sullair 900-350

LDH Parts

LDH Parts

Tons of LDH parts available – Call for needs.

Hydraulic Auger End

Hydraulic Auger End

2.625″ Hex Drive – Black Hydraulic Auger End

1995 Davey Kent DK50RA Crawler

1995 Davey Kent DK50RA Crawler

Crawler Rotary Drill Rig, 3 1/2 reg pin down, 3 rods, 2 spd wirth head, pullmaster winch, Moyno mud pump, model# PG-4, 4 cylinder diesel, air cooled, 8’6″H at lowest mast height, 53″ wide, Very god Condition. 3 extra tower sections included with rig.

ICE 50-50 Hydraulic Head

ICE 50-50 Hydraulic Head

ICE 50-50 Hydraulic Head. Re-Bearinged. Green

Cummins 6CT

Cummins 6CT

6CT Cummins – 220HP, 30k Miles w/ Transmission

Brayden Winch

Brayden Winch

Brayden Winch off of Grove Crane

Yale Electric Forklift

Yale Electric Forklift

Electric – 24 Volt Battery – 6,390 Hours

3,000lb capacity – 7,200lbs weight w/ Battery – 276″ Load Height – 10′ Tall – 41″ Wide

3 Available

DoAll Mill

DoAll Mill

Vertical or Horizontal Milling Machine

Caterpillar 3406 B

Caterpillar 3406 B

Caterpillar Diesel 3406 B 400hp – 5,000 hours

1988 Watson 2500

1988 Watson 2500

1988 Watson 2500 Cummins 6b 5.9 175hp low hours on engine, rebuilt pull master m25 inner bar winch, rebuilt tower cylinders, new inner/outer bar swivels, rebuilt hydraulic swivel, 81,000 ft-lbs torque. 25k crowd. 6″ and 4 1/4″ bars.      38′ 4”tall. 64,000 lbs

1982 Williams LDH60T

1982 Williams LDH60T

7” Outer Bar, 5 1/4” Inner Bar, Cummins 6BT, 175 HP, 6” Jacks, Mounted on 1982 Hendrickson Carrier Model 600-D0H, 4 axles

1990 Texoma Taurus XL

1990 Texoma Taurus XL

Mounted on CCC4 axle carrier with a CAT 3406 Engine, Up to 12′ Drilling Diameter, 120′ depth, Cummins 6 Cyl. Lower 144,000 ft-lbs torque, 38,000 Lbs. Hoist, 50,000 lbs Crowd

Texoma 650

Texoma 650

Mounted on a 2000 Peterbilt 379 Truck, 3 axle

1997 Watson 3100CW

1997 Watson 3100CW

New Cables, New Hydraulic Cylinders, New Engine, Rebuilt Turntable bearing, Tilting Carbody, 11’11” Wide, Up to 8′ Diameter, Up to 80’ Deep, Torque 113,000 ft-lbs, Crowd 50,000, Hoist 25,000.

Showing 1 - 30 of 40 items12>